top of page

Most common fault codes for Amana dryer

Here are some of the most common fault codes for Amana dryers, along with their meanings and possible solutions:


1. Error Code "F0" or "F1"

  • Meaning: Control Board Failure

  • Causes: This code indicates a failure in the main control board.

  • Solutions:

    • Unplug the dryer for a few minutes to reset the control board.

    • If the error persists, the control board may need to be replaced.


2. Error Code "F2"

  • Meaning: Door Switch Failure

  • Causes: The dryer door switch is not detecting the door is closed properly.

  • Solutions:

    • Check the door latch and switch to ensure they are functioning correctly.

    • Test the door switch for continuity. If it's defective, replace the switch.


3. Error Code "F3"

  • Meaning: Thermistor or Temperature Sensor Malfunction

  • Causes: The thermistor (temperature sensor) is faulty and not reading the correct temperature.

  • Solutions:

    • Test the thermistor for continuity using a multimeter.

    • If it’s defective, replace the thermistor.


4. Error Code "F4"

  • Meaning: Motor Fault or Overheating

  • Causes: This error appears if the dryer motor has overheated or is experiencing an internal fault.

  • Solutions:

    • Ensure the dryer is not overloaded.

    • Check the lint filter and vent for blockages.

    • If the motor is still faulty after cooling down, it may need to be replaced.


5. Error Code "F5"

  • Meaning: Control Panel Malfunction

  • Causes: The control panel is not working correctly, possibly due to a poor connection or component failure.

  • Solutions:

    • Check the control panel for any loose wires or visible damage.

    • If necessary, replace the control panel or the connections.


6. Error Code "F6"

  • Meaning: Heat Relay Failure

  • Causes: A problem with the relay that controls the heating element.

  • Solutions:

    • Check the relay for any signs of damage or wear.

    • If the relay is faulty, replace it.


7. Error Code "F7"

  • Meaning: Heating Element Failure

  • Causes: The heating element is not functioning, meaning the dryer will not heat up.

  • Solutions:

    • Inspect the heating element for damage or breakage.

    • If the heating element is defective, replace it.


8. Error Code "F8"

  • Meaning: Dryer Sensor Issue

  • Causes: The moisture sensor or another sensor within the dryer may not be working properly.

  • Solutions:

    • Clean the moisture sensor with a soft cloth to remove any buildup.

    • Test the sensor for continuity and replace it if necessary.


9. Error Code "PF"

  • Meaning: Power Failure

  • Causes: A power surge or interruption that causes the dryer to lose power.

  • Solutions:

    • Ensure the dryer is properly plugged in.

    • Check the circuit breaker and reset it if needed.

    • If the error persists, there may be an issue with the electrical supply.


10. Error Code "E1"

  • Meaning: Excessive Heat or Overheating

  • Causes: The dryer is overheating, typically due to restricted airflow or faulty temperature sensors.

  • Solutions:

    • Inspect the vent and lint filter for blockages.

    • Ensure that the temperature sensor is working properly and replace it if necessary.


11. Error Code "E2"

  • Meaning: Excessive Drying Time

  • Causes: This code usually appears when the dryer takes longer than usual to complete a cycle, typically due to poor airflow or blocked vents.

  • Solutions:

    • Clean the lint filter and exhaust vent.

    • Check the venting system for blockages or restrictions.


General Troubleshooting Tips for Amana Dryers:

  • Reset the Dryer: Power off the dryer by unplugging it for a few minutes to reset the control board and clear minor errors.

  • Check Venting System: Blockages in the vent hose or lint filter can cause overheating and extended drying times. Regularly clean these parts.

  • Test Components: Use a multimeter to test components like the thermistor, door switch, and heating element for continuity.

  • Inspect Wiring: Check all wiring and connections to ensure everything is properly secured.

Get virtual help with DIY jobs with our xPorch App

app_call_screen.PNG

xPorch © 2025

Ask Us Anything!

Get help from a virtual expderts to fix your home renovation

xPorch offers homeowners the power to complete basic DIY repairs and renovations without spending hundreds of dollars on service calls. With xPorch, DIYers are a couple of clicks aways from connecting with experienced plumbers, electricians, and contractors. Our team offers on-demand virtual services around the year around all Canadian provinces.

 

  • Instagram
  • Facebook

Terms & Conditions    Privacy Policy  

bottom of page