top of page

Most common fault codes for GE dryer

Here are some of the most common fault codes for GE dryers and their possible causes and solutions:


1. Error Code "E1"

  • Meaning: Thermistor Fault

  • Causes: The thermistor (temperature sensor) is malfunctioning, which affects the drying cycle and temperature regulation.

  • Solutions:

    • Check the thermistor for continuity with a multimeter.

    • If the thermistor is faulty, replace it.

    • Ensure there are no loose or damaged wires connected to the thermistor.


2. Error Code "E2"

  • Meaning: Motor Overload

  • Causes: The dryer motor is overworked or has an issue, leading to an overload condition.

  • Solutions:

    • Clean the lint filter and vent system to reduce strain on the motor.

    • Inspect the motor for any signs of wear or blockage.

    • If the motor is faulty, it may need to be replaced.


3. Error Code "E3"

  • Meaning: Temperature Sensor Fault

  • Causes: The temperature sensor that monitors the dryer’s internal temperature is not functioning properly.

  • Solutions:

    • Check the temperature sensor for continuity using a multimeter.

    • If defective, replace the temperature sensor.

    • Inspect the wiring for any loose or damaged connections.


4. Error Code "E4"

  • Meaning: Dryer Door Problem

  • Causes: The dryer door is either not closing properly, or the door switch is faulty.

  • Solutions:

    • Make sure the door is completely closed and latched securely.

    • Test the door switch for proper functionality. If it's faulty, replace it.

    • Check for any obstructions preventing the door from closing properly.


5. Error Code "E5"

  • Meaning: Heater Circuit Failure

  • Causes: There may be a malfunction in the heating circuit, such as a faulty heating element.

  • Solutions:

    • Inspect the heating element for visible damage and continuity with a multimeter.

    • If faulty, replace the heating element.

    • Check the wiring connections to ensure proper power flow to the heating circuit.


6. Error Code "E6"

  • Meaning: Dryer Control Board Malfunction

  • Causes: A fault in the dryer’s control board can prevent the unit from operating correctly.

  • Solutions:

    • Try unplugging the dryer for a few minutes to reset the control board.

    • Inspect the control board for visible damage or burnt components.

    • If the control board is faulty, it may need to be replaced.


7. Error Code "F0"

  • Meaning: Dryer Overheating

  • Causes: The dryer has overheated due to airflow issues, such as a clogged vent.

  • Solutions:

    • Clean the lint filter, vent hose, and exhaust system to ensure proper airflow.

    • Check for any obstructions in the vent line.

    • Inspect the temperature sensor and thermostat for proper operation, and replace if needed.


8. Error Code "F1"

  • Meaning: Faulty Control Board

  • Causes: The control board is experiencing an issue, either from a power surge or internal failure.

  • Solutions:

    • Unplug the dryer for a few minutes and then plug it back in to reset it.

    • If the error persists, test the control board for continuity and replace it if necessary.


9. Error Code "PF"

  • Meaning: Power Failure

  • Causes: A power outage or an electrical issue caused the dryer to lose power.

  • Solutions:

    • Ensure the dryer is properly plugged in and the circuit breaker is not tripped.

    • Check the power supply to ensure there is adequate voltage to operate the dryer.


10. Error Code "C1"

  • Meaning: Coin or Object in Drum

  • Causes: A foreign object (such as a coin) is stuck in the drum or vent system, causing an obstruction.

  • Solutions:

    • Check the dryer drum for any small objects or debris.

    • Inspect the vent system for blockages that may be caused by foreign objects.


11. Error Code "tE"

  • Meaning: Thermistor Failure

  • Causes: The thermistor (temperature sensor) is defective or disconnected.

  • Solutions:

    • Test the thermistor for continuity with a multimeter.

    • If it's faulty, replace the thermistor.


12. Error Code "t"

  • Meaning: Temperature Too High

  • Causes: The temperature inside the dryer is excessively high.

  • Solutions:

    • Check and clean the vent system to ensure proper airflow.

    • Test the thermostat and temperature sensor to ensure they are functioning correctly.


General Troubleshooting Tips for GE Dryer Error Codes:

  • Reset the Dryer: Unplug the dryer for a few minutes to reset the system and clear minor error codes.

  • Check Airflow: Blocked or restricted airflow due to lint buildup or obstructions is a common cause of overheating, motor failure, and temperature errors. Always clean the lint filter and the vent hose regularly.

  • Inspect Components: Test components like the thermostat, heating element, and thermistor with a multimeter to check for faults.

  • Check the Door: Ensure the door is properly closed, and test the door switch if needed.

  • Power Supply: Ensure the dryer is plugged into a working electrical outlet and that the circuit breaker has not tripped.

Get virtual help with DIY jobs with our xPorch App

app_call_screen.PNG

xPorch © 2025

Ask Us Anything!

Get help from a virtual expderts to fix your home renovation

xPorch offers homeowners the power to complete basic DIY repairs and renovations without spending hundreds of dollars on service calls. With xPorch, DIYers are a couple of clicks aways from connecting with experienced plumbers, electricians, and contractors. Our team offers on-demand virtual services around the year around all Canadian provinces.

 

  • Instagram
  • Facebook

Terms & Conditions    Privacy Policy  

bottom of page